§ 66270.25. Specific Part B Information Requirements for Equipment.

Except as otherwise provided in Section 66264.1, owners and operators of facilities that have equipment to which Article 28 of Chapter 14 applies must provide the following additional information:

(a) For each piece of equipment to which Article 28 of Chapter 14 applies:

(1) equipment identification number and hazardous waste management unit identification;

(2) Approximate locations within the facility (e.g., identify the hazardous waste management unit on a facility plot plan);

(3) type of equipment (e.g., a pump or pipeline valve);

(4) percent by weight total organics in the hazardous waste stream at the equipment;

(5) hazardous waste state at the equipment (e.g., gas/vapor or liquid); and

(6) methods of compliance with the standards (e.g., “monthly leak detection and repair” or “equipped with dual mechanical seals”).

(b) For facilities that cannot install a closed-vent system and control device to comply with the provisions of 40 CFR 264 subpart BB on the effective date that the facility becomes subject to the provisions of Chapter 14 or 15, Article 28, an implementation schedule as specified in Section 66264.1033(a)(2).

(c) Where an owner or operator applies for permission to use a control device other than a thermal vapor incinerator, catalytic vapor incinerator, flare, boiler, process heater, condenser, or carbon adsorption system and chooses to use test data to determine, the organic removal efficiency or the total organic compound concentration achieved by the control device, a performance test plan as specified in Section 966264.1035(b)(3).

(d) Documentation that demonstrates compliance with the equipment standards in Sections 66264.1052 to 66264.1059. This documentation shall contain the records required under Section 66264.1064. The Department may request further documentation before deciding if compliance has been demonstrated.

(e) Documentation to demonstrate compliance with Section 66264.1060 shall include the following information:

(1) a list of information references and sources used in preparing the documentation;

(2) records, including the dates of each compliance test required by Section 66264.1033(j);

(3) a design analysis, specifications, drawings, schematics, and piping and instrumentation diagrams based on the appropriate sections of “APTI Course 415: Control of Gaseous Emissions” (incorporated by reference as specified in Section 66260.11) or other engineering texts which the Department determines contain basic control device design information which is at least as protective of human health and environment as APTI Course 415: Control of Gaseous Emissions. The design analysis shall address the vent stream characteristics and control device operation parameters as specified in Section 66264.1035(b)(4)(C);

(4) a statement signed and dated by the owner or operator certifying that the operating parameters used in the design analysis reasonably represent the conditions that exist when the hazardous waste management unit is operating at the highest load or capacity level reasonably expected to occur;

(5) a statement signed and dated by the owner or operator certifying that the control device is designed to operate at an efficiency of 95 weight percent or greater.

(6) method of compliance with the standard (e.g., “monthly leak detection and repair” or “equipped with dual mechanical seals”).

HISTORY

1. New section filed 12-23-92; operative 1-22-93 (Register 93, No. 2).

2. Change without regulatory effect amending subsection (e)(2) filed 12-28-93 pursuant to title 1, section 100, California Code of Regulations (Register 93, No. 53).

3. Editorial correction of first paragraph (Register 95, No. 50).

4. Change without regulatory effect amending subsections (d), (e), (e)(3) and (e)(5) and deleting duplicate subsections (b) -(e)(5) filed 12-28-95 pursuant to section 100, title 1, California Code of Regulations (Register 95, No. 52).

Note

Note: Authority cited: Sections 25150 and 25159, Health and Safety Code. Reference: Sections 25159 and 25159.5, Health and Safety Code; 40 CFR Section 270.25.